| 1. | Secure the hood in the wide open position (support rod in the lower hole).
|
| 2. | Disconnect the negative cable from the battery first, then disconnect the positive cable. |
| 3. | Remove the battery. |
| 4. | Remove the under-cowl panel. |
| 5. | Remove the air cleaner housing assembly. |
| 6. | Remove the engine cover.
|
| 7. | Remove the air flow tube.
|
| 8. | Remove the harness clamp (A), then remove the two bolts (B) securing the clutch line bracket.
|
| 9. | Remove the harness clamp (A).
|
| 10. | Remove the battery base (B), then remove the battery base bracket (C). |
| 11. | Remove the harness clamp (A) and the air cleaner housing bracket (B), then remove the bracket (C).
|
| 12. | Remove the battery cables (A) from the under-hood fuse/relay box.
|
| 13. | Disconnect the engine wire harness connectors (B). |
| 14. | Remove the intercooler outlet hose.
|
| 15. | Remove the clutch slave cylinder and clutch line bracket mounting bolt. |
| 16. | Remove the shift cable. |
| 17. | Remove the shift cable bracket.
|
| 18. | Remove the fuel hose.
|
| 19. | Remove the fuel return hose (A) and brake booster vacuum hose (B).
|
| 20. | Remove the steering wheel. |
| 21. | Remove the steering joint cover (A).
|
| 22. | Make a reference mark (B) across the steering joint and steering gearbox pinion shaft. Remove the steering joint bolt (C), then disconnect the steering joint from the steering gearbox pinion shaft (D). |
| 23. | Remove the expansion tank cap. |
| 24. | Raise the vehicle on the hoist to full height. |
| 25. | Remove the front wheels. |
| 26. | Remove the engine undercover.
|
| 27. | Loosen the drain plug in the radiator, and drain the engine coolant. |
| 28. | Drain the engine oil. |
| 29. | Drain the transmission fluid. |
| 30. | Remove the catalytic converter/exhaust pipe A assembly.
|
| 31. | Disconnect the headlight adjuster front leveling sensor connector (With HID). |
| 32. | Separate the stabilizer links from the dampers. |
| 33. | Separate the tie-rod end ball joints from the knuckles. |
| 34. | Separate the knuckles from the lower arms. |
| 35. | Remove the driveshafts. Coat all precision-finished surfaces with clean engine oil. Tie plastic bags over the driveshaft ends. |
| 36. | Disconnect the connectors from the steering gearbox.
|
| 37. | Loosen the bands (A) securing the turbocharger outlet hose and intercooler intake hose, and remove the intercooler intake hose (B), then remove the intercooler intake pipe mounting bolts (C).
|
| 38. | Remove the intercooler intake pipe bracket (D), then remove the intercooler intake pipe (E). |
| 39. | Lower the vehicle on the hoist. |
| 40. | Remove the radiator. |
| 41. | Remove the A/C line from the clamp (A), and remove the water bypass hose (B).
|
| 42. | Remove the drive belt. |
| 43. | Remove the A/C compressor.
|
| 44. | Remove the heater hoses.
|
| 45. | Attach the chain hoist using the sling belt and karabiner to the engine/transmission as shown. NOTE:
|
| 46. | Make sure the hoist brackets are positioned properly. Raise the hoist to full height. |
| 47. | Remove the lower torque rod.
|
| 48. | Remove the subframe.
|
| 49. | Make sure the hoist brackets are positioned properly. Lower the vehicle on the hoist. |
| 50. | Remove the side engine mount upper bracket mounting bolt and nuts (A).
|
| 51. | Remove the ground cable (B). |
| 52. | Remove the transmission mounting bolt and nuts (A).
|
| 53. | Remove the ground cable (B). |
| 54. | Check that the engine/transmission is completely free of vacuum hoses, fuel and coolant hoses, and electrical wiring. |
| 55. | Slowly lower the engine/transmission assembly about 150 mm (6 in.). Check once again that all hoses and electrical wiring are disconnected and free from the engine/transmission, then lower it all the way. |
| 56. | Disconnect the chain hoist from the engine/ transmission assembly. |
| 57. | Raise the vehicle all the way, and remove the engine/transmission assembly from under the vehicle. |